haiku.git

/*
 * Copyright (c) 2012-2015 Haiku, Inc.
 *
 * Permission is hereby granted, free of charge, to any person obtaining
 * a copy of this software and associated documentation files
 * (the "Software"), to deal in the Software without restriction,
 * including without limitation the rights to use, copy, modify, merge,
 * publish, distribute, sublicense, and/or sell copies of the Software,
 * and to permit persons to whom the Software is furnished to do so,
 * subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be
 * included in all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
 * IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
 * CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
 * TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
 * SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
 *
 * Authors:
 *		Alexander von Gluck, kallisti5@unixzen.com
 */
#ifndef __PLATFORM_BCM283X_H
#define __PLATFORM_BCM283X_H


#define SIZE_4K 0x00001000

/*
 * Found in:
 * Broadcom BCM2835 ARM Peripherals
 *  - BCM2835-ARM-Peripherals.pdf
 */

// Section 1.2.2
// These board bases should go away when we start using FDT's
// (all loader drivers compiled in, drivers chosen based on FDT)
//
#define BCM283X_SDRAM_BASE		0x00000000
#define BCM2835_PERIPHERAL_BASE	0x20000000
#define BCM2836_PERIPHERAL_BASE	0x3f000000


// Added to physical addresses to select the different cache behaviours
#define BCM283X_VIDEO_CORE_L1_L2_CACHED		(0 << 30)
#define BCM283X_VIDEO_CORE_L2_COHERENT		(1 << 30)
#define BCM283X_VIDEO_CORE_L2_CACHED		(2 << 30)
#define BCM283X_VIDEO_CORE_UNCACHED			(3 << 30)

// The highest two bits are used to select aliases to the physical memory
// with different cache semantic. Clearing them converts the address to
// physical memory as seen by ARM.
#define BCM283X_BUS_TO_PHYSICAL(x)			(x & ~BCM283X_VIDEO_CORE_UNCACHED)


#define ST_BASE			0x3000
	// System Timer, sec 12.0, page 172
#define DMA_BASE		0x7000
	// DMA Controller, sec 4.2, page 39
#define ARM_BASE		0xB000
	// BCM283X ARM Control Block, sec 7.5, page 112
#define PM_BASE			0x100000
	// Power Management, Reset controller and Watchdog registers
#define GPIO_BASE		0x200000
	// GPIO, sec 6.1, page 90
#define UART0_BASE		0x201000
	// UART 0, sec 13.4, page 177
#define MMCI0_BASE		0x202000
	// MMC
#define UART1_BASE		0x215000
	// UART 1, sec 2.1, page 65
#define EMMC_BASE		0x300000
	// eMMC interface, sec 5, page 66
#define SMI_BASE		0x600000
	// SMI Base
#define USB_BASE		0x980000
	// USB Controller, 15.2, page 202
// FB_BASE will depend on memory split


// 7.5, page 112
#define ARM_CTRL_BASE			(ARM_BASE + 0x000)
#define ARM_CTRL_IC_BASa		(ARM_BASE + 0x200)
	// Interrupt controller
#define ARM_CTRL_TIMER0_1_BASE	(ARM_BASE + 0x400)
	// Timer 0 and 1
#define ARM_CTRL_0_SBM_BASE		(ARM_BASE + 0x800)
	// ARM Semaphores, Doorbells, and Mailboxes


/* UART */
// TODO: Check these UART defines!
#define UART_RHR    0
#define UART_THR    0
#define UART_DLL    0
#define UART_IER    1
#define UART_DLH    1
#define UART_IIR    2
#define UART_FCR    2
#define UART_EFR    2
#define UART_LCR    3
#define UART_MCR    4
#define UART_LSR    5
#define UART_MSR    6
#define UART_TCR    6
#define UART_SPR    7
#define UART_TLR    7
#define UART_MDR1   8
#define UART_MDR2   9
#define UART_SFLSR  10
#define UART_RESUME 11
#define UART_TXFLL  10
#define UART_TXFLH  11
#define UART_SFREGL 12
#define UART_SFREGH 13
#define UART_RXFLL  12
#define UART_RXFLH  13
#define UART_BLR    14
#define UART_UASR   14
#define UART_ACREG  15
#define UART_SCR    16
#define UART_SSR    17
#define UART_EBLR   18
#define UART_MVR    19
#define UART_SYSC   20


/* Mailbox */
#define ARM_CTRL_0_MAILBOX_BASE				(ARM_CTRL_0_SBM_BASE + 0x80)

#define ARM_MAILBOX_READ					0x00
#define ARM_MAILBOX_STATUS					0x18
#define ARM_MAILBOX_WRITE					0x20

#define ARM_MAILBOX_FULL					(1 << 31)
#define ARM_MAILBOX_EMPTY					(1 << 30)

#define ARM_MAILBOX_DATA_MASK				0xfffffff0
#define ARM_MAILBOX_CHANNEL_MASK			0x0000000f

#define ARM_MAILBOX_CHANNEL_FRAMEBUFFER		1

#endif /* __PLATFORM_BCM283X_H */